China high quality China Factory Customization High Transmission Efficiency Slasher Gearbox Speed Reducer spurs gear

Product Description

Product Description

China Factory customization High transmission efficiency slasher gearbox speed reducer

HangZhou Fubao Electromechanical Technology Co., Ltd. slasher gearbox speed reducer is a new generation of practical products independently developed by our company:

Low noise: less than 65db.

Low back clearance: up to 3 arc minutes in a CZPT and 5 arc minutes in a double stage.

High torque: higher than the standard planetary reducer torque.

High stability: high strength alloy steel, the whole gear after hardening treatment, not only the surface hard substitution.

High deceleration ratio: Modular design, planetary gearbox can be interlinked.

slasher gearbox speed reducer characteristic:

1.Planetary reducer manufacturer-Fubao Electromechanical Technology adopts an integrated planetary carrier and output shaft, which can provide better torsional rigidity. After precision machining, the gear set is not easy to eccentric, which can reduce interference, reduce wear and noise, and at the same time use a large The bearings are arranged with a wide span to distribute the load of the bearings, and once again strengthen the torque rigidity and radial load capacity of the slasher gearbox speed reducer. The output cover is made of aluminum alloy, which provides better heat dissipation capability for the product, so that the reducer produced by Fubao Electromechanical Technology can play an excellent role in the field of mechanical tools.

2.The planetary gear set is specially made of alloy steel. First, it undergoes quenching and tempering heat treatment to make the material hardness reach HRC30 degrees, and then undergoes nitriding surface treatment to HV860, so that the product has the characteristics of high surface hardness and high toughness in the center, and achieves the best product strength and service life. optimization.

3.The input shaft and the motor output shaft are connected by a bolted structure, with a round shaft seal design, and through dynamic balance analysis, it can ensure that there is no eccentric load at high speeds. After reducing unnecessary radial force, it can effectively Reduce the load on the motor side.

4.The material of the input cover/motor connection seat is made of aluminum alloy, which can provide better heat dissipation effect, and then provide good concentricity and verticality through professional lathe processing, so that the product can be stably combined with various motors, reducing the damage caused by insufficient precision. Unnecessary axial radial force makes the product have a longer life cycle.

WAB series parameters Model number WAB042 WAB60 WAB090 WAB115 WAB140 WAB180 WAB220
Rated output torque 14-22 23-60 48-160 140-330 342-650 520-1200 1140-2000
Reduction ratio L1: 3, 4, 5, 6, 7, 8, 9, 10    L2: 15, 20, 25, 30, 35, 40, 50, 70, 80, 100
Planetary gear backlash L1: P0≤1 P1≤3 P2≤5   L2: P0≤3 P1≤5 P2≤7

 

Detailed Photos

Product Details

Other products

Product Advantage

Compared with other reduction machines, planetary gear reduction machines have high rigidity, high precision (single stage can be achieved within 1 point), high transmission efficiency (single stage in 97-98%), high torque/volume ratio, lifetime maintenance free and other characteristics.

Because of these characteristics, planetary gear reducer is mostly installed on the stepper motor and servo motor, used to reduce speed, increase torque, matching inertia.

Company Profile

HangZhou Fubao Electromechanical Technology Co., Ltd. was established in 2008, the company has a complete precision reducer design, production capacity. Set R & D, manufacturing, assembly and sales, more in the field of gear manufacturing has more than 10 years of background, in the manufacturing equipment is equipped with Switzerland Riesenhahl gear grinding machine, domestic Qinchuan gear grinding machine, hamai gear hobbing machine and domestic Xihu (West Lake) Dis. gear hobbing machine, Japan Yasaki TLGmazak CNC lathe, CNC milling machine and other fully CNC equipment, In addition, it is equipped with other advanced measuring equipment such as Japanese TTI gear detector, 3 coordinate measurement, reducer backlash measurement instrument and so on. In a strong manufacturing capacity at the same time, can be stable, continuous manufacturing of high-quality precision reducer products.

The precision reducer produced by our company has the characteristics of high structural rigidity, small back backlash, precise transmission and so on. It is widely used in various industries. Companies adhering to the concept of let customers participate in manufacturing, and strive to provide customers with more personalized services. In the field of precision transmission has a unique achievements. It is our CZPT pursuit to make far-reaching contributions.

 

Factory Display

Q: Speed reducer grease replacement time
A: When sealing appropriate amount of grease and running reducer, the standard replacement time is 20000 hours according to the aging condition of the grease. In addition, when the grease is stained or used in the surrounding temperature condition (above 40ºC), please check the aging and fouling of the grease, and specify the replacement time.

Q: Delivery time
A: Fubao has 2000+ production base, daily output of 1000+ units, standard models within 7 days of delivery.

Q: Reducer selection
A: Fubao provides professional product selection guidance, with higher product matching degree, higher cost performance and higher utilization rate.

Q: Application range of reducer
A: Fubao has a professional research and development team, complete category design, can match any stepping motor, servo motor, more accurate matching.

Shipping Cost:

Estimated freight per unit.



To be negotiated
Application: Motor, Machinery, Agricultural Machinery, Ball Screw Drive Shaft
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Customization:
Available

|

Customized Request

screw gear

What lubrication is required for screw gears?

Proper lubrication is essential for the efficient and reliable operation of screw gears, also known as worm gears. The lubrication requirements for screw gears depend on various factors, including the application, operating conditions, and the materials used in the gear system. Here’s a detailed explanation of the lubrication considerations for screw gears:

Selection of Lubricant:

When selecting a lubricant for screw gears, it is important to consider the following factors:

  • Type of Lubricant: There are different types of lubricants available, such as oils, greases, and solid lubricants. The selection depends on factors such as operating speed, temperature range, load capacity, and environmental conditions. Consult the gear manufacturer’s recommendations or industry standards to determine the suitable lubricant type for the specific application.
  • Viscosity: The lubricant viscosity should be chosen based on the operating conditions of the screw gear system. Higher viscosity lubricants are typically used for heavier loads or higher temperatures, while lower viscosity lubricants are suitable for lighter loads or lower temperatures. The viscosity should be within the range recommended by the gear manufacturer.
  • Additives: Some lubricants contain additives that provide additional benefits, such as improved anti-wear properties, corrosion resistance, or extreme pressure protection. Consider the specific requirements of the screw gear system and choose a lubricant with suitable additives, if necessary.

Lubrication Guidelines:

Here are some general guidelines for lubricating screw gears:

  • Initial Lubrication: Apply an appropriate amount of lubricant during the initial installation of the screw gear system. Ensure that all gear surfaces, including the worm and the worm wheel, are adequately coated with lubricant.
  • Replenishment: Regularly monitor the lubricant level and condition of the screw gear system. Over time, lubricant may degrade, become contaminated, or lose its effectiveness. Follow the manufacturer’s recommendations for lubricant replenishment intervals and quantities. In some cases, lubricant replenishment may be necessary during routine maintenance.
  • Proper Lubricant Distribution: Ensure that the lubricant is evenly distributed across the contacting surfaces of the screw gears. The lubricant should adequately cover the threads of the worm and the teeth of the worm wheel to reduce friction and wear. Proper lubricant distribution can be achieved through rotational movement of the gears or by applying the lubricant directly to the contact area.
  • Prevent Excessive Lubrication: While proper lubrication is essential, excessive lubrication can lead to problems such as overheating, increased drag, and leakage. Follow the manufacturer’s recommendations regarding the appropriate lubricant quantity. Avoid over-greasing or over-oiling the screw gear system.
  • Cleanliness: Maintain cleanliness when lubricating screw gears. Ensure that the lubrication equipment, such as grease guns or oilers, is clean and free from contaminants. Contaminants, such as dirt or debris, can compromise the lubricant’s performance and increase wear on the gears.

It is important to note that the lubrication requirements may vary based on the specific screw gear system and its operating conditions. Therefore, always refer to the gear manufacturer’s recommendations and guidelines for the most accurate and up-to-date information regarding lubrication requirements.

screw gear

How do you ensure proper alignment when connecting screw gears?

Ensuring proper alignment when connecting screw gears is crucial for their efficient and reliable operation. Proper alignment helps minimize noise, vibrations, and premature wear, resulting in improved performance and longevity of the gear system. Here’s a detailed explanation of how to ensure proper alignment when connecting screw gears:

  • Use Precision Machining: Achieving accurate alignment starts with precision machining of the gear components. The worm gear and worm wheel should be machined to tight tolerances, ensuring proper tooth profile, pitch, and concentricity. High-quality manufacturing processes help ensure the components are dimensionally accurate, which facilitates proper alignment.
  • Consider Mounting Configuration: The mounting configuration plays a significant role in aligning screw gears. Whether the gear system is mounted on a shaft or a frame, it is important to carefully follow the manufacturer’s guidelines or engineering specifications for proper mounting. This may involve using specific mounting hardware, such as flanges, couplings, or adapters, to ensure secure and precise alignment.
  • Verify Axial Alignment: Axial alignment refers to the alignment of the worm gear and the worm wheel along the gear’s axis of rotation. To verify axial alignment, measurements such as center distance, parallelism, and axial runout should be taken. Precision measuring tools, such as dial indicators or laser alignment systems, can be used to ensure the components are aligned within the specified tolerances.
  • Check Radial Alignment: Radial alignment refers to the alignment of the worm gear and the worm wheel in the radial direction. It ensures that the gear meshing occurs at the proper contact point along the gear teeth. Radial alignment can be checked by measuring the radial runout or tooth contact pattern. Adjustments can be made by shimming or using spacers to achieve the desired alignment.
  • Consider Preloading: Preloading the screw gear system can help improve alignment and reduce backlash. Preloading involves applying a controlled axial force to the gear components to eliminate any clearance or play between the teeth. This can be achieved through various methods, such as using adjustable bearings or applying a preloaded spring mechanism. Preloading should be done within the manufacturer’s recommendations to avoid excessive loading that could lead to premature wear or damage.
  • Follow Manufacturer Guidelines: Manufacturers often provide specific guidelines and recommendations for aligning their screw gear products. These guidelines may include recommended tolerances, alignment procedures, and suggested tools or techniques. It is important to carefully review and follow these guidelines to ensure proper alignment and to maintain any warranty or support provided by the manufacturer.
  • Consult with Experts: If you are unsure about the alignment process or encounter challenges in aligning screw gears, it is beneficial to consult with experts or experienced engineers. They can provide guidance, troubleshooting assistance, or even perform precision alignment using specialized equipment or techniques.

By following these practices and taking the necessary alignment measures, you can ensure proper alignment when connecting screw gears. This alignment process helps optimize the performance, efficiency, and service life of the gear system.

screw gear

Are there different types of screw gears available?

Yes, there are different types of screw gears available, each with its variations in design and functionality. These variations cater to specific applications and requirements. Here are some of the commonly used types of screw gears:

  • Single-Thread Worm Gears: Single-thread worm gears have a single helical thread on the worm. They provide a relatively higher gear ratio and are commonly used in applications requiring moderate torque and precision positioning. Single-thread worm gears are widely employed in industries such as manufacturing, automotive, and machinery.
  • Multi-Thread Worm Gears: Multi-thread worm gears have multiple helical threads on the worm, typically two or more. The presence of multiple threads increases the contact area and allows for higher torque transmission. Multi-thread worm gears offer higher gear reduction ratios and are suitable for applications requiring greater torque multiplication, such as heavy-duty machinery and high-load lifting systems.
  • Fine-Pitch Worm Gears: Fine-pitch worm gears have a smaller pitch, meaning there are more teeth per unit length of the worm. This design allows for finer control and precise positioning. Fine-pitch worm gears find applications in industries where accurate motion control is critical, such as robotics, automation, and optics.
  • Coarse-Pitch Worm Gears: Coarse-pitch worm gears have a larger pitch, resulting in fewer teeth per unit length of the worm. This design provides higher torque transmission and is suitable for applications requiring heavy-duty power transmission. Coarse-pitch worm gears are commonly used in industries like manufacturing, material handling, and conveyors.
  • Right-Handed and Left-Handed Worm Gears: Screw gears can be classified as right-handed or left-handed based on the direction of the helical thread. In a right-handed worm gear, the helical thread advances in a clockwise direction when viewed from the end of the worm. In a left-handed worm gear, the helical thread advances counterclockwise. The choice between right-handed and left-handed worm gears depends on the specific application and the desired rotational direction.
  • Non-Throated and Throated Worm Gears: Non-throated worm gears have a cylindrical worm without a groove, while throated worm gears have a groove or a notch on the worm. The presence of a throat allows for greater contact between the worm and the worm wheel, increasing the gear meshing efficiency and load-carrying capacity. Throated worm gears are commonly used in applications where higher efficiency and load capacity are required.
  • Self-Locking Worm Gears: Self-locking worm gears are designed to have a high self-locking capability. The helical thread angle and the friction between the worm and the worm wheel prevent the worm wheel from backdriving the worm when the system is at rest. Self-locking worm gears are widely used in applications that require holding a position without the need for additional braking or locking mechanisms, such as elevators, lifts, and positioning systems.

These are some of the different types of screw gears available in the market. The selection of a specific type depends on factors such as torque requirements, gear reduction ratio, precision positioning, load capacity, and self-locking capabilities, among others. Understanding the characteristics and variations of screw gears allows for choosing the most suitable type for a given application.

China high quality China Factory Customization High Transmission Efficiency Slasher Gearbox Speed Reducer spurs gearChina high quality China Factory Customization High Transmission Efficiency Slasher Gearbox Speed Reducer spurs gear
editor by CX 2023-09-05

Tags: