China Hot selling Swl Series Portable Linear Motion Mechanical Car Lift Lifting Equipment Electric or Manual 5ton Engine Reducer Worm Gear Lifter Screw Jack with Motor with Hot selling

Product Description

SWL Series Portable linear Motion Mechanical Car Lift lifting Equipment Electric or Manual 5Ton Engine Reducer Worm Gear Lifter Screw Jack with Motor

 

Product  Description

 

Our Jack’s Advantages:

-Self-locking ability
-Can be driven directly by motor or other power or manual
-Can be customized according user’s demand
-Compact configuration, small size, lightweight
-Convenient installation, flexible operation
-High reliability and stability
-2 Sets, 3 Sets, 4 Sets, 8 Sets etc. Screw Jacks to linkage to use ( Screw Jacks Linkage Use Application, see the below)

Technical data

1. Lift speed: 150mm/min~1800mm/min
2. Input power:0.5 -21.8KW
3. Screw rang: 5-16 mm
4. Bearing range: 2T-100T
5. Structure: motor direct connection, single & double shaft

Model

SWL2.5

SWL5

SWL10

SWL15

SWL20

SWL25

SWL35

Max Capacity (KN)

25

20

100

150

200

250

350

Lifting screw

Tr30*6

Tr40*7

Tr58*12

Tr58*12

Tr65*12

Tr90*16

Tr100*20

Ratio (P)

6:1

8:1

23:3

23:3

8:1

32:3

32:3

Ratio (M)

24:1

24:1

24:1

24:1

24:1

32:1

32:1

Raise per revolution (mm) (P)

1.0

0.875

1.565

1.565

1.56

1.5

1.875

Raise per revolution (mm) (M)

0.250

0.292

0.5

0.5

0.5

0.5

0.625

Start torque on lifting screw at max load

250

385

500

400

490

850

820

400

770

1000

800

980

1700

1640

Starting torque/Handwind torque at max load (Nm) (P)

18

39.5

119

179

240

368

464

Starting torque/Handwind torque at max load (Nm)(M)

8.86

19.8

60

90

122

217

253

Running efficiency (%)(P)

33

23

20.5

20.5

19.5

16

18

Running efficiency (%) (M)

11

11.5

13

13

12.8

9

11

Weight without spindle or protection tube (Kg)

7.3

16.2

25

25

36

70.5

87

Weight of lifting screw 100 mm (kg)

0.45

0.82

1.67

1.67

2.15

4.15

5.20

Lubrication

ZGN-1 or ZGN-2 (-20-+100)

Grease quantity

0.1

0.3

0.5

0.5

0.75

1.1

1.9

Click here for more models!
 

Related Products

Our Company

Ever-power specialist in making all kinds of mechanical transmission and hydraulic transmission like: planetary gearboxes, worm reducers, in-line helical gear speed reducers, parallel shaft helical gear reducers, helical bevel reducers, helical worm gear reducers, agricultural gearboxes, tractor gearboxes, auto gearboxes, pto drive shafts, special reducer & related gear components and other related products, sprockets, hydraulic system, vaccum pumps, fluid coupling, gear racks, chains, timing pulleys, udl speed variators, v pulleys, hydraulic cylinder, gear pumps, screw air compressors, shaft collars low backlash worm reducers and so on. furthermore, we can produce customized variators, geared motors, electric motors and other hydraulic products according to customers’ drawings.
The company provides a reliable gurantee for the product’ s quality by advanced inspection and testing equipment. professional technical team, exquisite processing technology and strict control system.
In recent years, the company has been developing rapidly by its rich experience in production, adcanced managemant system, standardized management system, strong technical force. We always adhere the concept of survial by quality, and decelopment by innovation in science and technology.
Ever-power Group is willing to work with you hand in hand and create brilliance together! 
 

FAQ

Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.

Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shippment.

Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.

If you have another question, please feel free to contact us

 

Application: Motor, Electric Cars, Motorcycle, Machinery, Marine, Agricultural Machinery, Car
Function: Distribution Power, Clutch, Change Drive Torque, Change Drive Direction, Speed Changing, Speed Reduction, Speed Increase
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Steel
Samples:
US$ 9999/Piece
1 Piece(Min.Order)

|
Request Sample

screw gear

What lubrication is required for screw gears?

Proper lubrication is essential for the efficient and reliable operation of screw gears, also known as worm gears. The lubrication requirements for screw gears depend on various factors, including the application, operating conditions, and the materials used in the gear system. Here’s a detailed explanation of the lubrication considerations for screw gears:

Selection of Lubricant:

When selecting a lubricant for screw gears, it is important to consider the following factors:

  • Type of Lubricant: There are different types of lubricants available, such as oils, greases, and solid lubricants. The selection depends on factors such as operating speed, temperature range, load capacity, and environmental conditions. Consult the gear manufacturer’s recommendations or industry standards to determine the suitable lubricant type for the specific application.
  • Viscosity: The lubricant viscosity should be chosen based on the operating conditions of the screw gear system. Higher viscosity lubricants are typically used for heavier loads or higher temperatures, while lower viscosity lubricants are suitable for lighter loads or lower temperatures. The viscosity should be within the range recommended by the gear manufacturer.
  • Additives: Some lubricants contain additives that provide additional benefits, such as improved anti-wear properties, corrosion resistance, or extreme pressure protection. Consider the specific requirements of the screw gear system and choose a lubricant with suitable additives, if necessary.

Lubrication Guidelines:

Here are some general guidelines for lubricating screw gears:

  • Initial Lubrication: Apply an appropriate amount of lubricant during the initial installation of the screw gear system. Ensure that all gear surfaces, including the worm and the worm wheel, are adequately coated with lubricant.
  • Replenishment: Regularly monitor the lubricant level and condition of the screw gear system. Over time, lubricant may degrade, become contaminated, or lose its effectiveness. Follow the manufacturer’s recommendations for lubricant replenishment intervals and quantities. In some cases, lubricant replenishment may be necessary during routine maintenance.
  • Proper Lubricant Distribution: Ensure that the lubricant is evenly distributed across the contacting surfaces of the screw gears. The lubricant should adequately cover the threads of the worm and the teeth of the worm wheel to reduce friction and wear. Proper lubricant distribution can be achieved through rotational movement of the gears or by applying the lubricant directly to the contact area.
  • Prevent Excessive Lubrication: While proper lubrication is essential, excessive lubrication can lead to problems such as overheating, increased drag, and leakage. Follow the manufacturer’s recommendations regarding the appropriate lubricant quantity. Avoid over-greasing or over-oiling the screw gear system.
  • Cleanliness: Maintain cleanliness when lubricating screw gears. Ensure that the lubrication equipment, such as grease guns or oilers, is clean and free from contaminants. Contaminants, such as dirt or debris, can compromise the lubricant’s performance and increase wear on the gears.

It is important to note that the lubrication requirements may vary based on the specific screw gear system and its operating conditions. Therefore, always refer to the gear manufacturer’s recommendations and guidelines for the most accurate and up-to-date information regarding lubrication requirements.

screw gear

Can screw gears be used in both vertical and horizontal orientations?

Yes, screw gears, also known as worm gears, can be used in both vertical and horizontal orientations. The suitability of screw gears for a particular orientation depends on several factors. Here’s a detailed explanation of using screw gears in vertical and horizontal orientations:

Vertical Orientation:

Screw gears can be used in vertical orientations, such as when the worm gear is positioned vertically above or below the worm wheel. However, there are some considerations to keep in mind:

  • Self-Locking Capability: One advantage of screw gears is their self-locking capability, which means they can hold position without additional braking mechanisms. In vertical orientations, this self-locking feature can be beneficial, especially when the load needs to be held in position without the need for external support or brakes.
  • Lubrication: Proper lubrication is crucial in vertical screw gear applications to ensure efficient power transmission and minimize wear. Gravity can affect lubricant distribution, so it is essential to use lubricants with appropriate viscosity and ensure adequate lubrication reaches all gear surfaces even in a vertical configuration.
  • Load and Torque: The weight of the load being transmitted through the screw gear system is an important consideration in vertical orientations. Vertical applications often involve lifting or supporting heavy loads, and the torque requirements can be high. It is important to ensure that the screw gear system is designed to handle the specific load and torque demands of the vertical application.

Horizontal Orientation:

Screw gears can also be used in horizontal orientations, where the worm gear and worm wheel are positioned parallel to the ground. Here are some considerations for using screw gears in horizontal orientations:

  • Lubrication: Proper lubrication is still important in horizontal screw gear applications to minimize friction, wear, and heat generation. The lubricant viscosity and type should be chosen to provide adequate film thickness and reduce sliding friction between the gear surfaces.
  • Efficiency: Screw gears generally have lower mechanical efficiency compared to some other gear types. In horizontal orientations, where efficiency is critical for power transmission, it is important to consider the gear design and material selection to minimize energy losses and maximize the overall system efficiency.
  • Load Distribution: In horizontal orientations, the load distribution between the worm gear and the worm wheel is typically more uniform compared to vertical orientations. This can help reduce tooth stresses and increase the overall stability of the gear system.
  • Mounting and Support: Proper mounting and support of the screw gear system are important in horizontal orientations to ensure alignment and minimize vibrations. Adequate support structures, such as rigid bases or frames, should be used to maintain the gear system’s stability and integrity.

In summary, screw gears can be used in both vertical and horizontal orientations. However, the specific application requirements, including load, torque, lubrication, and efficiency considerations, should be carefully evaluated to ensure the screw gear system is suitable and designed to meet the demands of the particular orientation.

screw gear

Can you explain the concept of screw gear threads and their functions?

Screw gear threads play a crucial role in the operation and functionality of screw gears, also known as worm gears. The threads are an essential component of the worm, which is the cylindrical gear with a helical thread wrapped around it. Here is a detailed explanation of the concept of screw gear threads and their functions:

  • Thread Design: The threads on a screw gear, specifically the helical thread on the worm, are designed in a helical shape, resembling the threads of a screw. The helical thread is wrapped around the cylindrical body of the worm, creating a continuous spiral path along its length. The pitch of the thread refers to the distance between successive thread crests or valleys.
  • Meshing with Worm Wheel: The primary function of the screw gear threads is to mesh with the teeth of the worm wheel. The helical thread of the worm engages with the teeth of the worm wheel, creating a sliding contact between them. As the worm rotates, the helical thread drives the rotation of the worm wheel, transmitting rotational motion and power.
  • Gear Reduction and Torque Multiplication: The helical design of the screw gear threads allows for a large number of teeth on the worm wheel to be engaged at any given time. This results in a high gear reduction ratio, meaning that for each revolution of the worm, the worm wheel rotates by a smaller fraction. The gear reduction ratio enables torque multiplication, making screw gears suitable for applications requiring high torque output.
  • Precision Positioning: Screw gear threads are crucial for achieving precise positioning in applications where accuracy is essential. The fine pitch of the helical thread allows for small incremental movements, enabling precise control over the rotation of the worm wheel. This feature is particularly advantageous in applications such as robotics, where accurate positioning and motion control are necessary.
  • Self-Locking Action: The helical thread design of screw gears gives them a self-locking capability. When the worm is not rotating, the friction between the helical thread and the teeth of the worm wheel tends to hold the gear system in place. This self-locking action prevents the worm wheel from backdriving the worm, providing inherent braking or locking functionality. It ensures that the gear mechanism maintains its position without the need for additional braking or locking mechanisms.
  • Efficiency and Lubrication: The sliding action between the screw gear threads and the teeth of the worm wheel introduces more friction compared to other types of gears with rolling motion. This sliding motion affects the efficiency of the gear mechanism, resulting in higher energy losses and heat generation. Proper lubrication with appropriate lubricants is essential to minimize wear, reduce friction, and improve the overall efficiency of the screw gears.

Overall, screw gear threads enable the meshing and transmission of rotational motion and power between the worm and the worm wheel. They facilitate gear reduction, torque multiplication, precise positioning, and self-locking action. Understanding the design and functions of screw gear threads is crucial for utilizing screw gears effectively in various applications.

China Hot selling Swl Series Portable Linear Motion Mechanical Car Lift Lifting Equipment Electric or Manual 5ton Engine Reducer Worm Gear Lifter Screw Jack with Motor with Hot sellingChina Hot selling Swl Series Portable Linear Motion Mechanical Car Lift Lifting Equipment Electric or Manual 5ton Engine Reducer Worm Gear Lifter Screw Jack with Motor with Hot selling
editor by CX 2023-09-25

Tags: